Full Site Search
Subscribe
To get our newsletter please enter your email address in the box below and press 'Subscribe' button.

Need help !?
You don't know which one to choose or you still have some questions left.

Contact our expert by email and we will call you back.comten email

Call us
comten email

Knowledge Base   Categories

Knowledge Base   Latest

The force gauge Centor Touch has 3 inputs and 6 outputs trigger channels for a direct connection to a logic controller, or production machine. The trigger channels allow synchronization of Centor touch gauge with external events (External events such as brake pedal depression or passing a marker point).

 read more...read more...

Peeling tests are the practice of testing adhesion properties of film bonded to substrate, usually by tensile. The peel strength determines the adhesive strength (also called the adhesive fracture toughness).

 read more...read more...

The acquisition of data using a control commanded equipment and software, is a non negligible potential advanced ability and it can have an effect on materials testing. But is that necessary to capture all those information?

 

 read more...read more...

One of the original and most commonly used method of attaching parts together is by means of a threaded fastener, however the threaded joint and its fastening is a complicated matter.

 read more...read more...

In the design and manufacturing industries, torque measurement is a big challenge and becomes a relevant measurement in order to define / validate:

 

  • mounting specifications / clamping
  • product characteristics such as motors, generators, wind turbines ...
  • the accuracy of tools such as wrenches or screwdrivers

 read more...read more...
centormeter keyIn the world of manufacturing and assembly, measurement of torque tightening of fasteners is imperative for the effectiveness of production and product quality. On one hand, loose attachment may vibrate or loosen, on the other hand if the torque is too high a bold can break. Faced with these problems, manufacturers are realizing that a well-managed torque system can make the difference between a safe, reliable, economic product and a complete disaster.  read more...read more...

A Force Gauge is a measuring instrument used across all industries to measure the force during a push or pull test. Applications exist in research and development, laboratory, quality, production and field environment. There are two kind of force gauges today: mechanical and digital force gauges.

 read more...read more...

RessortMeasuring forces of a spring is one of the most important test to determine the quality of a springs. Indeed all the springs are designed to have an expected force at a particular height, it is essential to validate the calculations and especially the manufacturing parameters by measuring forces.

 read more...read more...

The peel strength is the measure of the average force to part to bonded materials.

 read more...read more...

In order to improve the setup of cap screwing machine, Com-Ten Industries has designed force and torque gauges with special sensors to measure directly on the machine. These testers are called "measuring bottles" and can measure torque or force.

 read more...read more...

Puncture tests are used to evaluate the properties of thin materials at break, puncture or drill. To measure these properties, a penetrator or needle is applied with a constant speed on the material to a failure or to a predetermined elongation.

 read more...read more...

Topload tests or Crush tests are specially designed to ensure the resistance of bottles, cans or drums during the filling process or transportation. These tests can easily detect defects in production to avoid most of the problems during filling, storage, shipping or crating.

 read more...read more...

It is sometimes really hard to measure the torque on caps. The quality of the measure depends on different parameters: material, operator, torque tester. So you can have important differences between results and it is impossible to have a good repeatability. Com-Ten Industries gives you advises to improve you measurements.

 read more...read more...
At some point, manufacturers will find themselves in this situation: they have to test their new product in manufacturing - the question is how to do it. What equipment should they choose? What is the best device to use to ensure good results? How can production be validated without getting the boss upset about the budget?  read more...read more...
A Torque Gauge is measuring instrument used across all industries to measure the torque or torsion during a test. Applications exist in research and development, laboratory, quality, production and field environment. There are two kind of force gauges today: mechanical and digital torque gauges.  read more...read more...

The coefficient of friction is the ratio of the frictional force to the force acting perpendicular to the two surfaces in contact.

 read more...read more...
Your Cart
Your shopping cart is empty!
Become a distributor!
Consider becoming a Com-Ten distributor today. Read the advantages of Com-Ten distributor and download our terms and conditions.


ISO9001:2008 Certified

Com-Ten Industries, for force gauge, pull tester and torque tester products

Measuring force from Apple to Zipper since 1960.
6405 49th Street North, Pinellas Park, FL 33781 • Phone: 727-520-1200 • Fax: 727-520-0299 • sales@com-ten.com
SecurityMetrics for PCI Compliance, QSA, IDS, Penetration Testing, Forensics, and Vulnerability Assessment